Sliding Gate Motor VDS Simply SL600 (Kit-Complete) P
- For a maximum leaf weight of 600kg
- Non-reversible, permanently lubricated mechanism
- Up to 12 open/close cycles per hour. (at 20°C)
- Up to 30 open/close cycles per day.
- Single-phase motor (230 VAC)
- Mechanism dimensions: 230x210x230 mm (LxWxH)
- Leaf movement speed: 10 m/min
- Motor absorbed power: 250 W
- Motor thermal protection: 120 °C
- Features a key-operated door for manual release
- Protection rating: IP44
- The gear type is Z12/module 4. (12 teeth)
- Plastic rack module 4
- Country of origin: Italy
To order this product, please call us at 210.555.0632 or buy it online from our eshop.
The VDS Simply SL600 (Kit-Complete) P set contains:
- VDS Simply SL600 sliding garage door mechanism for 600kg gate.
- Mechanism mounting base with screws and anchors
- Manual release keys for mechanism (2 pcs)
- Limit switch activation plates
- Detailed instructions written in Greek
- ProfelmNet PSD-36T remote control at 433.92 MHz, 3 pcs
- Metal rack, 4m
- Wired photocells, 1 set
- Warning light, 1 pc
The VDS Simply SL600 (Kit-Standard) P set is a complete kit for installing a mechanism on a garage door. Other materials can be added to it depending on your needs.
Criteria for installing the VDS Simply SL600 mechanism on your gate
- It can be installed on a gate leaf with a maximum weight of 600kg.
- It can be used up to 12 times per hour.
- It can be used up to 40 times per day.
600kg of gate weight is a quite high limit if we assume that the average weight of sliding gates is usually 60-70kg/m. However, if the gate weight is not known, it is advisable to ask the manufacturer. From our experience, the above mechanism covers most sliding gate cases.
The 12 uses per hour cover even a small apartment building, as the gate can operate every 5 minutes during peak hours. The motor has thermal protection. This means that if the use is exceeded and it overheats, the movement stops until the normal temperature is restored. It is logical that short gates, in a cold environment, can make more movements than large gates in a hot environment. If the motor stops moving due to overheating, the gate must be operated manually.
The daily uses can cover, for example, 10 cars that will use it 4 times a day. These uses (compared to the hourly uses) are the optimal operation for the mechanism to last for many years without problems.
Sliding garage door with mechanism - Features
A classic sliding gate arrangement with a mechanism naturally includes the gate leaf which has wheels at its bottom. The wheels must be well maintained so as not to hinder the movement of the gate and the mechanism.
The rail, on which the wheels move, is firmly secured to the ground. The rail must be straight, without bumps or deformations.
The door leaf is held upright by rollers. The rollers are positioned so that they are always in contact with the door from the fully open to the fully closed position. They must be stable and not allow the door to deviate from its path, but without hindering its movement. They are placed at the top of the door and in the middle of its travel.
The last accessories (for a non-motorized door) are the mechanical door stops. The stops define the door's travel, i.e., its final position for both opening and closing.
To automate a gate leaf, we install a metal (or plastic) rack. The rack is a toothed bar that cooperates with the motor's gear to transmit movement.
The motor is placed in the center of the door's travel so that it always maintains contact with the door. It has a gear that transmits movement from the mechanism to the door via the rack.
Beyond the mechanism, an essential accessory for the safety of the entire construction are the safety photocells. The safety photocells are placed on either side of the opening and check for obstacles in the door's path. If an obstacle is detected during the closing of the door, the photocells send a command to the mechanism's control panel, and the door's closing stops.
Also, for even greater safety, a safety flashing light could be installed, which provides a visual signal when the door is in operation. This is usually installed when the door is adjacent to busy roads, roads with heavy traffic, and in areas where visibility is limited.
Finally, in cases where the range of the remote controls is not as desired, an external antenna can be installed to amplify the signal.
Base for VDS Simply SL600 sliding automation
The mechanism comes with a base specially designed for proper and robust support. The foundation should ideally be concrete to ensure that the mechanism is properly supported. The diagram below shows the detailed dimensions of the VDS Simply SL600 mechanism base. The base has two holes which are placed on the left as we look at the door from the side where the rack (and the mechanism) is located.
To install the base of the sliding mechanism, follow these steps:
- Check the subfloor and wiring. (the best solution is a reinforced concrete subfloor with a spiral conduit for the wiring)
- Attach the square nuts to the bottom of the base.
- Install the base in place with metal expansion anchors (also known as "knock-in" anchors).
Position of the base of the VDS Simply SL600 sliding automation
The base of the sliding garage door mechanism must be placed in a specific position for the motor to function correctly. Below, the position where the base should be placed is defined in detail, depending on whether the door opens to the right or to the left. (left and right are defined as looking at the door from the side where the motor and rack are installed)
To find the correct position of the base, we follow this procedure:
- Push the door leaf, by hand, to the fully closed position. Place the mechanism base on the ground, at a distance of at least B from the edge of the door leaf.
- Push the door leaf, by hand, to the open position. The base must be at a distance C from the edge of the door. If this is true, the installation proceeds. If this condition is not met, there are the following 2 options:
- We compromise with the fact that the door leaf will not open completely (but will open to the point where it reaches a distance C from the base). We choose this solution if the free opening is sufficient and what remains continues to meet our needs.
- We extend the length of the door, by extending the door leaf. It can be extended along its entire height or only at the point where it comes into contact with the rack.
Mechanism installation (height) - Detailed dimensions
The installation height of the mechanism is extremely important for the entire installation process. What matters is the height in relation to the rack for their proper cooperation. Many times, the design of the door determines where the rack will be placed so that there are support points for the rack on the door. Below are detailed drawings for the installation height of the mechanism in the case where the rack has been placed with its teeth facing downwards. (this is the recommended and most common solution)
H1= 18mm (motor mounting base height)
H2=72mm (top of base to top of gear)
H3=15mm (top of gear to rack spacer axis)
H1+H2+H3=H1+H4+H5=105mm (bottom of base to rack spacer axis)
H4=67mm (top side of base to bottom of rack)
H5=20mm (bottom of rack to rack spacer axis)
H6=10mm (spacer axis to top of rack)
H1+H4=85mm (bottom of base to bottom of rack)
Ho= height of raised foundation (the base can be placed in a raised position for spatial reasons. In this case, the motor is protected, e.g. in case of flood.
Based on the above dimensions, a preliminary check is performed before the installation of the mechanism. There are two cases:
- If there is already a rack, we check if the height at which it has already been placed is suitable in relation to the dimensions of the mechanism and the height at which its gear is located. If the dimensions do not match, either we will have to raise the mechanism's base (if the rack is high) or change the rack's position. (uninstall and reinstall)
- If there is no rack already, we check if there are available mounting points on the door for the rack at the desired installation height. Otherwise, we will have to install the entire structure higher by shaping the subfloor where the mechanism's base will be placed.
Plastic rack
The plastic rack is delivered in pieces 34cm long. It is plastic on the outside with a metal core for greater durability. The rack's cross-section is 12x30mm, the diametral pitch is 4 (module 4), and it has 2 supports and 2 sets of screws with rectangular nuts per piece. It can be installed on door leaves with a maximum weight of 800kg.
A key point of attention is the clearance that must exist between the gear and the rack. Ideally, this clearance should be 1.5mm.
If this gap does not exist, the mechanism is forced to carry the gate along its entire path instead of simply pushing it. This will cause wear and tear and sooner or later problems will arise in its operation. The installation is done by welding it onto the gate.
In the opposite case where the gap is large, the cooperation between the gear and the rack will not be correct and jerks and stresses will be created on the motor. Therefore, special care is required to create this gap.
Metal gear for VDS SL600 sliding mechanism
The metal gear reliably transmits movement from the mechanism to the garage door via the rack. It features protection to prevent accidents and the entrapment of objects between the gear and the rack.
Autotech S5060T control panel for sliding garage door mechanisms
The Autotech S5060T control panel is included in the set and is integrated into the mechanism. It is a control panel that combines simplicity of use with all necessary functions and has been time-tested. It combines perfectly with the VDS SL600 mechanism.
Technical characteristics:
- It has a socket for the mechanism's limit switches.
- We can adjust the mechanism's force.
- There is the possibility for smooth start and stop for less wear and tear on the mechanism and the garage door.
- It accepts safety photocells which interrupt movement when they encounter an obstacle when the door closes and start the reverse movement (opening).
- There is an available setting for automatic door closing with a user-selectable closing start time. The use of photocells is necessary for the automatic closing function.
- There is the option of electric braking.
- The opening direction is set with a microswitch.
- The panel can accept a push-button (keypad or simple push-button).
- The panel can accept a 230VAC warning light without a flasher or a 230VAC lighting lamp.
- It has a built-in receiver with simple operation.
- User information about the mechanism's functions is provided by LED lights.
The above control panel has been tested by thousands of users and has proven to be extremely reliable. In addition, it features functions such as adjusting the mechanism's force, slow start and stop, which make it one of the best choices on the market today.
ProfelmNet PSD-36T remote controls at 433.92 MHz.
ProfelmNet PSD-36T remote controls have an excellent design and are easy and simple to use and program. They have been tested by thousands of users and do not present problems. They can accept up to four commands from different mechanisms, which makes them convenient for users who have more than one automation in their daily use.
Sliding mechanism installation procedure - Summary
In summary, the steps for installing a sliding garage door mechanism are as follows:
- Check that the door operates smoothly manually.
- Check the wiring if it exists or lay new wiring.
- After the checks, the motor base is installed. It requires a stable foundation. Usually, a reinforced concrete base is the appropriate solution.
- Mounting the motor on the base.
- Installation of the rack.
- Installation of accessories
- Checking the proper functioning of the construction and explaining all the details for safe use to the users.
The above are simply a summary of the steps for installing a sliding mechanism. Inside the mechanism's packaging, you will find detailed, step-by-step instructions, well-written and easy to follow.
Manual operation of the VDS SL600 sliding mechanism
The manual operation procedure of the VDS SL600 mechanism is simple and easy for all users. With the key, we open the release door and push it to the fully open position. The garage door now operates manually. By reversing the process (closing and locking the door), we re-engage the mechanism.
Packaging of the VDS Simply SL600 (Kit-Complete) P mechanism set
The VDS Simply SL600 (Kit-Complete) P set is delivered in two packages. One contains the mechanism, the remote control, and any accessories that may have been ordered separately from the set.
The second package contains only the plastic rack due to weight.
The set is delivered ready for installation as it has been checked by our technicians and the remote control is configured.
Installation instructions for the sliding garage door kit
The set is delivered with detailed instructions in Greek. These have been processed by us to be easy to follow even by people who are not directly familiar with the subject.
They contain detailed steps for each stage of the installation, from the motor base and the rack to accessories such as photocells and buttons. Detailed instructions for the Autotech S-5060T control panel, which is integrated into the mechanism, are also included.