The MEKO-5 (Kit-Standard) S kit includes:

• MEKO-5 sliding gate mechanism suitable for gate leaf weights up to 500Kg.
• Autotech S5060T control panel
• ProfelmNet PSD-36T remote controls at 433.92 MHz, 2 pcs
• 4m metal rack
• Pair of wired safety photocells
• Motor mounting base (with mounting screws and anchors)
• Limit switch activation plates
• Manual release with key, 2 pcs
• Greek installation instructions

The above proposal is a basic but reliable solution for installing a mechanism with all necessary products. Of course, products can be added to the above kit to fully meet your needs.

The Proteco Meko-5 mechanism has quite good specifications and can cover most sliding garage door cases. Specifically:

• It is suitable for garage doors with a maximum weight of 500kg.
• It can operate safely and without problems up to 12 times per hour.
• It can operate safely and without problems up to 30 times per day.

As for the weight of the gate, you should ask its manufacturer. However, most sliding driveway gates weigh around 60-70kg/m. So in most cases, 500kg is a limit that is quite safe and a typical residential garage door will rarely reach it.

The uses per hour are sufficient for an average garage door as it can operate every five minutes during peak hours. It should be noted here that if the motor overheats, it will stop operating until it returns to normal operating conditions. It has thermal protection to protect itself from excessive use.

Finally, the uses per day can cover most cases of a residential garage door. The uses per day are a limit so that the motor does not wear out prematurely and lasts for many years without problems.

Dimensions of Proteco Meko-5 mechanism

With a height and length of 31cm, the Proteco Meko 5 motor can be installed on most sliding garage doors. Also, with a width of less than 20cm, it fits even in cases where there is not much space.

A typical sliding garage door setup naturally includes the gate leaf, which has wheels at its bottom. The wheels must be well-maintained to avoid hindering the movement of the gate and the mechanism.

The wheels move on a rail which must be firmly fixed to the ground. The rail must be straight, without bumps or deformations.

The rollers hold the gate perpendicular to the ground. They are placed in the middle of the path so that they always have contact with the gate. They must be stable and not allow the gate to deviate from its path, but without hindering its movement.

Finally (for a gate without a mechanism), the last accessories are the mechanical stops of the gate. These define the final position of the gate for both opening and closing.

Next, to automate the gate, we install the metal (or plastic) rack on the gate leaf. The rack is a toothed bar that works with the motor's gear to transmit movement.

The motor is installed in the center of the gate's travel so that it is always in contact with the gate. It has a gear that transmits movement from the mechanism to the gate via the rack.

Beyond the mechanism, an essential accessory for the safety of the entire construction are the safety photocells. Safety photocells are placed on either side of the opening and check if there is an obstacle in the gate's path. If an obstacle is detected while the gate is closing, the photocells signal the mechanism's control panel, and the gate stops closing.

Also, for even greater safety, a safety flashing light could be installed, which gives a signal when the gate is in operation. This is usually installed when the gate is adjacent to busy roads, roads with heavy traffic, and in areas where visibility is limited.

Finally, in cases where the remote controls' range is not desired, an external antenna can be installed to amplify the signal.

The following describes the wiring required for a sliding garage door mechanism and for all accessories that can be added (not all accessories are included in this set)

• The Proteco Meko-5 mechanism requires a 3x1.5mm² cable suitable for outdoor use. If the distance from the electrical panel is large, it would be advisable to install a 3x2.5mm² cable. In any case, it is good for the mechanism's wiring to start from a separate fuse from the electrical panel.
• Wired photocells require 4x0.6mm² cables for the receiver and 2x0.6mm² for the transmitter. If photocells with a reflector are used, then only a 4x0.6mm² cable is required up to the transceiver. Reflector photocells cost a little more, but if the wiring has not been laid, they provide an immediate solution without alterations and extra work.
• The keyed button (keypad) or the simple button requires a 2x0.6mm² cable.
• The warning light requires a 1x1.0 mm² or 2x1.0 mm² cable.

Wiring should be done by a qualified electrician. Particular attention must be paid to protecting the cables from moisture, as these installations are outdoors.

Autotech S5060T control panel for sliding garage door mechanisms

The Autotech S5060T control panel is included in the set and is integrated into the mechanism. It is a control panel that combines simplicity of use with all the necessary functions and has been proven over time. It pairs perfectly with the Proteco Meko 5 mechanism.

Technical characteristics:

• It has a socket for the mechanism's limit switches
• We can adjust the mechanism's force.
• There is the possibility of soft start and stop for less wear and tear on the mechanism and the garage door.
• It accepts safety photocells that stop movement when they encounter an obstacle when the door is closing and initiate reverse movement (opening).
• There is an available setting for automatic door closing with the user's choice of closing start time. The use of photocells is essential for automatic closing.
• There is an option for electric braking.
• The opening direction is adjusted with a microswitch.
• The panel can accept a button (keyed or simple push-button).
• The panel can accept a 230VAC warning light without a flasher or a 230VAC lighting lamp.
• It has an integrated receiver with simple operation.
• User information about the mechanism's functions is provided by LED lights.

The above control panel has been tested by thousands of users and has proven to be extremely reliable. In addition, it has features such as adjusting the mechanism's force, slow start and stop, which make it one of the best choices on the market at the moment.

ProfelmNet PSD-36T sliding gate mechanism remote control

The ProfelmNet PSD-36T remote control is tested and reliable. It has 4 buttons to which we can set 4 different mechanisms (swing gates, roller shutters, overhead garage doors, etc.). It has a fixed 12-bit code at 433.92 MHz. It has a modern design and works excellently with the Autotech S5060T control panel.

Metal rack for sliding garage door mechanism

The metal rack is the most common solution for use on metal sliding driveway gates. The metal rack consists of one-meter pieces, with a diametral pitch of 4 (module 4) and a cross-section of 12x30mm. Each piece includes 3 spacers. It is installed on gates with a maximum weight of 2 tons and is galvanized for greater resistance to outdoor conditions.

During installation, the spacers are welded onto the gate. The rack is then screwed onto the spacers. The rack has oval holes for the spacer screws. This allows for small adjustments of the rack's height.

During the installation of the metal rack, particular attention must be paid to the necessary clearance between the gear and the rack. This gap should ideally be 1.5mm. This gap is such that the rack cooperates perfectly with the gear. If the gap is larger, the rack will "kick" and the movement of the gate will not be smooth. If this gap does not exist and the rack touches the gear, the mechanism is forced to carry the gate, and sooner or later it will wear out and develop a fault.

Operation of sliding gate photocells

Photocell sensors are a product that significantly increases safety in the use of a sliding mechanism at minimal cost. These specific photocells (IR5001P) are extremely reliable and operate with 12-24 VDC or 12-24 VAC, making them compatible with most control panels on the market. They have been on the market for years and do not present problems. They require no maintenance and are quite reliable even in difficult weather conditions.

Photocell operation method: The transmitter emits an infrared light beam, in the invisible spectrum, which is directed towards the receiver. When there is no obstacle to interrupt the beam, the gate operates normally. When the beam is interrupted by an obstacle (vehicle, pedestrian, pet, etc.) during the closing of the gate, the control panel instructs the mechanism to stop the closing of the gate and to start the reverse movement (opening). If the beam is interrupted while the gate is opening, it continues its normal course, while if it is open, it is not allowed to start closing.

An alternative to wired photocells is the installation of photocells with a reflector. These photocells do not require wiring from both sides of the gate, so they are easier to install. They are preferred in cases where the gate and the surrounding area have been completed without provision for wiring. They have a small surcharge compared to wired photocells, but they are a very good solution when wiring cannot be laid.

Brief installation process for sliding mechanism

The steps for installing a sliding garage door mechanism are as follows:

• Check that the gate operates smoothly manually.
• Check for existing wiring or install it.
• After the checks, proceed with the installation of the motor base. A stable foundation is required. Usually, a reinforced concrete base is the appropriate solution.
• Mount the motor on the base.
• Install the rack.
• Install accessories (if any).
• Check for proper operation of the system and explain all details for safe use to the users.

The above are just a brief overview of the installation steps for a sliding mechanism. Inside the mechanism's packaging, you will find detailed, step-by-step instructions, well-written and easy to follow, even for people with no direct experience in the field.

Disengagement of Proteco Meko-5 sliding automation

For increased safety, the Proteco Meko-5 mechanism is disengaged with a key. Insert the release key into the lock and unlock it. Then open the small door to its fully open position, and the motor now operates manually. The mechanism is re-engaged by reversing the process (locking the small door).

Proteco Meko 5 mechanism gear

The gear of the Proteco Meko-5 mechanism is metallic for greater durability and reliability. It has a protective cover to prevent accidents and protect users.

Packaging of the MEKO-5 (Kit-Standard) S mechanism kit

The MEKO-5 (Kit-Standard) S kit is delivered in two packages. The first package contains the mechanism, the remote control, and its accessories.

The second package contains only the metallic rack, which consists of one-meter pieces.

The kit is delivered ready for installation, as it has been checked by our technicians and the remote control is set up.

Installation instructions for the sliding garage door kit

The kit comes with detailed instructions in Greek. They have been processed by us to be easy to follow even by people who are not directly familiar with the subject.

They contain detailed steps for each stage of installation, from the motor base and rack to accessories such as photocells and buttons. Detailed instructions for the Autotech S-5060T control panel integrated into the mechanism are also included.

Available documents for the Proteco Meko-5 motor (in English)

CE Declaration of Conformity

Installation Manual

Commercial brochure for Proteco Meko sliding automation