VDS Simply SL600 Sliding Gate Operator Kit (Kit-Basic)
- For maximum gate leaf weight of 600kg
- Non-reversible, permanent lubrication mechanism
- Up to 12 open/close cycles per hour. (at 20°C)
- Up to 30 open/close cycles per day.
- Single-phase motor (230 VAC)
- Mechanism dimensions: 230x210x230 mm (LxWxH)
- Gate leaf speed: 10 m/min
- Motor absorbed power: 250 W
- Motor thermal protection: 120 °C
- Features a key-operated door for disengagement (manual operation)
- Protection rating: IP44
- Gear type is Z12/module 4.
- Country of origin: Italy
- Warranty: 2 years
To order this product, please call us at 210.555.0632 or buy it online from our eshop.
The VDS Simply SL600 kit (Kit-Basic) includes:
- VDS Simply SL600 sliding gate opener for 600kg gate with all its accessories:
- Mechanism mounting base with screws and anchors
- Manual release keys (2 pcs)
- Limit switch activation tabs
- Detailed instructions written in Greek
- ProfelmNet PSD-36T remote control at 433.92 MHz, 1 pc
The VDS Simply SL600 (Kit-Basic) set is an initial kit for installation on a garage door that has a rack. Other materials can be added to it depending on your needs.
Criteria for installing the VDS Simply SL600 mechanism on your gate
- It can be installed on a gate leaf with a maximum weight of 600kg.
- It can be used up to 12 times per hour.
- It can be used up to 40 times per day.
The 600kg gate weight is a fairly high limit, assuming that the average weight of sliding gates is usually 60-70kg/m. However, if the gate weight is not known, it is advisable to ask the manufacturer. From our experience, the above mechanism covers most sliding gate cases.
The 12 uses per hour cover even a small apartment building, as the gate can operate every 5 minutes during peak hours. The motor has thermal protection. This means that if the use is exceeded and it overheats, movement is interrupted until the normal temperature returns. It is logical that short gates, in a cold environment, can perform more movements than large gates in a warm environment. If the motor stops due to overheating, the gate must be operated manually.
The daily uses can cover, for example, 10 cars that will use it 4 times a day. These uses (compared to the hourly uses) are the optimal operation for the mechanism to last for many years without problems.
Sliding garage door with mechanism - Features
A classic sliding gate arrangement with a mechanism naturally includes the gate leaf, which has wheels at its bottom. The wheels must be well maintained to avoid hindering the movement of the gate and the mechanism.
The rail, on which the wheels move, is securely fastened to the ground. The rail must be straight without bumps or deformations.
The gate leaf is held upright by the rollers. The rollers are positioned so that they are always in contact with the gate from the fully open to the fully closed position. They must be stable and not allow the gate to deviate from its path, but without hindering its movement. They are placed at the top of the gate and in the middle of its travel.
The last accessories (for a gate without a mechanism) are the mechanical stops of the gate. The stops define the gate's travel, i.e., its final position both when opening and closing.
To automate a gate leaf, we install a metal (or plastic) rack. The rack is a toothed bar that cooperates with the motor's pinion to transmit movement.
The motor is placed in the center of the gate's travel so that it is always in contact with the gate. It has a pinion that transmits movement from the mechanism to the gate via the rack.
In addition to the mechanism, an essential accessory for the safety of the entire structure are the safety photocells. The safety photocells are placed on either side of the opening and check for obstacles in the gate's path. If an obstacle is detected during the gate's closing, the photocells instruct the mechanism's control panel to stop the gate from closing.
Also, for even greater safety, a safety beacon could be installed, which gives a visual signal when the gate is in operation. It is usually installed when the gate is adjacent to busy roads, roads with heavy traffic, and in areas where visibility is limited.
Finally, in cases where the remote control range is not desired, an external antenna can be installed to amplify the signal.
Base for VDS Simply SL600 sliding automation
The mechanism comes with a base specially designed for proper and sturdy support. The sub-base should preferably be made of concrete to ensure that the mechanism is properly supported. The diagram below shows the detailed dimensions of the VDS Simply SL600 mechanism base. The base has two holes that are placed to the left as you look at the gate from the side where the rack (and the mechanism) is located.
To install the base of the sliding mechanism, follow these steps:
- Check the sub-base and the wiring. (the best solution is a reinforced concrete sub-base with a conduit for the wiring)
- Attach the square nuts to the bottom of the base.
- Install the base in position with metal expansion anchors (also known as "knock-in").
Positioning the base of the VDS Simply SL600 sliding automation
The base of the sliding garage door mechanism must be placed at a specific point for the motor to operate correctly. Below, the exact point where the base should be placed is defined, depending on whether the door opens to the right or to the left. (left and right are defined as looking at the door from the side where the motor and the rack are installed)
To find the correct position of the base, we follow this procedure:
- Push the gate leaf manually to the fully closed position. Place the mechanism's base on the ground, at a distance of at least B from the edge of the gate leaf.
- Push the gate leaf manually to the open position. The base must be at a distance C from the edge of the gate. If this is true, the installation proceeds. If this condition is not met, there are 2 options:
- We accept that the gate leaf will not open fully (but will open to the point where it reaches a distance C from the base). We choose this solution if the free opening is sufficient and what remains continues to meet our needs.
- We extend the length of the gate by extending the gate leaf. It can be extended along its entire height or only at the point where it comes into contact with the rack.
Mechanism installation (height-wise) - Detailed dimensions
The installation height of the mechanism is extremely important for the entire installation process. What matters is the height in relation to the rack for their proper cooperation. Often, the gate's design determines where the rack will be placed so that there are support points for the rack on the gate. Below are detailed diagrams for the height of the mechanism's installation when the rack is placed with the teeth downwards (this is the recommended and most common solution).
H1 = 18mm (height of motor mounting base)
H2 = 72mm (top of base to top of gear)
H3 = 15mm (top of gear to rack spacer axis)
H1+H2+H3 = H1+H4+H5 = 105mm (bottom of base to rack spacer axis)
H4 = 67mm (top side of base to bottom of rack)
H5 = 20mm (bottom of rack to rack spacer axis)
H6 = 10mm (spacer axis to top of rack)
H1+H4 = 85mm (bottom of base to bottom of rack)
Ho = height of elevated foundation (the base can be placed at an elevated point for positioning reasons. In this case, the motor is protected, e.g., in case of flooding).
Based on the above dimensions, a preliminary check is performed before installing the mechanism. There are two cases:
- If a rack already exists, we check if the height at which it is already installed is suitable in relation to the dimensions of the mechanism and the height at which its gear is positioned. If the dimensions do not match, we will either have to raise the mechanism's base (if the rack is high) or change the rack's position (uninstall and reinstall).
- If there is no existing rack, we check if there are available mounting points on the gate for the rack at the desired installation height. Otherwise, we will have to place the entire structure higher by shaping the sub-base where the mechanism's base will be placed.
A key point of attention is the gap that must exist between the gear and the rack. Ideally, this gap should be 1.5mm.
If this gap does not exist, the mechanism is forced to carry the gate along its entire path instead of simply pushing the gate. This will cause wear and tear and sooner or later problems will arise in its operation.
In the opposite case, if the gap is large, the cooperation between the gear and the rack will not be correct and jerks and stresses will be created in the motor. Therefore, special attention is required to create this gap.
Metal gear for VDS SL600 sliding mechanism
The metal gear reliably transmits movement from the mechanism to the garage door via the rack. It features protection to prevent accidents and the entrapment of objects between the gear and the rack.
Autotech S5060T control panel for sliding gate mechanisms
The Autotech S5060T control unit is included in the kit and is integrated into the mechanism. It is a control unit that combines simplicity of use with all the necessary functions and has been time-tested. It combines perfectly with the VDS SL600 mechanism.
Technical specifications:
- It has a socket for the mechanism's limit switches.
- We can adjust the mechanism's force.
- There is the possibility for soft start and stop for less wear and tear on the mechanism and the garage door.
- It accepts safety photocells which interrupt movement when they detect an obstacle during the closing of the door and initiate reverse movement (opening).
- There is an available setting for automatic door closing with the user choosing the closing start time. The use of photocells is essential for the automatic closing function.
- There is an option for electric braking.
- The opening direction is adjusted by a microswitch.
- The panel can accept a push-button (keypad or simple push-button).
- The panel can accept a 230VAC warning light without a flasher or a 230VAC lighting lamp.
- It has a built-in receiver with simple operation.
- User information regarding the mechanism's functions is provided by LED lights.
The above control panel has been tested by thousands of users and has proven to be extremely reliable. In addition, it has features such as adjusting the mechanism's force, slow start and stop, which make it one of the best choices currently on the market.
ProfelmNet PSD-36T remote controls at 433.92 MHz.
ProfelmNet PSD-36T remote controls feature an excellent design while being easy to use and simple, both in their operation and programming. They have been tested by thousands of users and do not present problems. They can accept up to four commands from different mechanisms, which makes them convenient for users who have more than one automation in their daily use.
Sliding mechanism installation procedure - Summary
In brief, the steps for installing a sliding garage door mechanism are as follows:
- Checking that the door operates smoothly manually.
- Checking the wiring if it exists or routing it.
- After the checks, the motor base is installed. A stable sub-base is required. Usually, a reinforced concrete base is the appropriate solution.
- Mounting the motor on the base.
- Mounting the rack.
- Installation of accessories (if any).
- Checking the proper functioning of the assembly and explaining all details for safe use to the users.
The above are simply a summary of the steps for installing a sliding mechanism. Inside the mechanism's packaging, you will find detailed, step-by-step instructions, well-written and easy to follow.
Manual operation of VDS SL600 sliding mechanism
The manual override process for the VDS SL600 mechanism is a simple and easy procedure for all users. With the key, open the release door and push it to the fully open position. The garage door now operates manually. By reversing the process (closing and locking the door), we re-engage the mechanism.
Packaging of the VDS Simply SL600 mechanism set (Kit-Basic)
The VDS Simply SL600 (Kit-Basic) set is delivered in one package containing the mechanism, the remote control, and any accessories that may have been ordered extra from the set.
The set is delivered ready for installation as it has been checked by our technicians and the remote control is programmed.
Installation instructions for the sliding garage door set
The set comes with detailed instructions in Greek. They have been processed by us to be easy to follow even by people who are not directly involved in the field.
They contain detailed steps for each stage of installation from the motor base and the rack to accessories such as photocells and buttons. Also included are detailed instructions for the Autotech S-5060T control panel which is integrated into the mechanism.