The MEKO-5 (Kit-Basic) set includes:

• MEKO-5 sliding garage door mechanism suitable for gate leaf weight up to 500Kg.
• Autotech S5060T control panel
• ProfelmNet PSD-36T remote control at 433.92 MHz, 1 pc
• Motor mounting base (with mounting screws and anchors)
• Terminal switch activation plates
• Manual release with key, 2 pcs
• Greek installation instructions

The above proposal is an economical but reliable solution for installing a mechanism in cases where a rack already exists. Of course, products can be added to the above kit to fully meet your needs.

The Proteco Meko-5 mechanism has very good specifications and can cover most sliding garage door cases. In detail:

• It is suitable for garage doors with a maximum weight of 500kg.
• It can operate safely and without problems up to 12 times per hour.
• It can operate safely and without problems up to 30 times per day.

Regarding the weight of the door, you should ask its manufacturer. However, most sliding gates weigh around 60-70kg/m. So, in most cases, 500kg is a limit that is quite safe and a typical residential garage door will hardly reach it.

The uses per hour are sufficient for an average garage door since it can operate every five minutes during peak hours. We should note here that if the motor overheats, it will stop operating until it returns to normal operating conditions. It has thermal protection to protect itself from excessive use.

Finally, the uses per day can cover most cases of residential garage doors. The uses per day constitute a limit so that the motor does not wear out earlier than normal and lasts for many years without problems.

Proteco Meko-5 mechanism dimensions check

With a height and length of 31cm, the Proteco Meko 5 motor can be installed on most sliding garage doors. Also, with a width of less than 20cm, it fits even in cases where space is limited.

A typical sliding garage door layout naturally includes the gate leaf, which has wheels at its bottom. The wheels must be well maintained to avoid hindering the movement of the door and the mechanism.

The wheels move on a rail which must be firmly fixed to the ground. The rail must be straight without bumps and deformations.

Rollers hold the door perpendicular to the ground. They are placed in the middle of the travel path so that they always maintain contact with the door. They must be stable and not allow the door to deviate from its path, but without hindering its movement.

Finally (for a door without a mechanism), the last accessories are the mechanical door stops. These define the final position of the door for both opening and closing.

Then, to automate the door, we mount the metal (or plastic) rack on the gate leaf. The rack is a toothed bar that works with the motor's gear to transmit movement.

The motor is placed in the center of the door's travel path so that it always maintains contact with the door. It has a gear that transmits movement from the mechanism to the door via the rack.

Beyond the mechanism, an essential accessory for the safety of the entire construction are the safety photocells. Safety photocells are placed on either side of the opening and check for obstacles in the door's path. If an obstacle is detected during the door's closing, the photocells signal the mechanism's control panel, and the door stops closing.

Also, for even greater safety, a safety beacon could be installed, which signals when the door is in operation. This is usually installed when the door is adjacent to busy roads, roads with heavy traffic, and in areas where visibility is limited.

Finally, in cases where the range of the remote controls is not desirable, an external antenna can be installed to amplify the signal.

The following details the wiring required for a sliding garage door mechanism and all accessories that can be added (not all accessories are included in this specific set)

• The Proteco Meko-5 mechanism requires a 3x1.5mm² cable suitable for outdoor use. If the distance from the electrical panel is long, it would be advisable to install a 3x2.5mm² cable. In any case, it is good for the mechanism's wiring to start from a separate fuse in the electrical panel.
• Wired photocells require 4x0.6mm² cables for the receiver and 2x0.6mm² for the transmitter. If photocells with a reflector are used, then only one 4x0.6mm² cable is required up to the transceiver. Reflector photocells cost a little more, but if the wiring has not been laid, they provide an immediate solution without major repairs and extra work.
• The key button (keypad) or the simple button requires a 2x0.6mm² cable.
• The warning light requires a 1x1.0 mm² or 2x1.0 mm² cable.

Wiring should ideally be done by a qualified electrician. Particular attention must be paid to protecting the cables from moisture, as these installations are outdoors.

Autotech S5060T control panel for sliding garage door mechanisms

The Autotech S5060T control panel is included in the set and is integrated into the mechanism. It is a control panel that combines simplicity of use with all necessary functions and has been tested over time. It works perfectly with the Proteco Meko 5 mechanism.

Technical characteristics:

• It has a socket for the mechanism's limit switches
• We can adjust the mechanism's force.
• There is the possibility for soft start and stop for less wear and tear on the mechanism and the garage door.
• It accepts safety photocells which interrupt movement when they encounter an obstacle during the door's closing and start the reverse movement (opening).
• There is an available setting for automatic door closing with the user choosing the closing start time. The use of photocells is essential for the automatic closing function.
• There is an option for electric braking.
• The opening direction is adjusted with a microswitch.
• The panel can accept a button (keypad or simple push button).
• The panel can accept a 230VAC warning light without a flasher or a 230VAC lighting lamp.
• It has a built-in receiver with simple operation.
• User information regarding the mechanism's functions is provided by LED lights.

The above control panel has been tested by thousands of users and has proven to be extremely reliable. In addition, it has functions such as adjusting the mechanism's force, slow start and stop, which make it one of the best choices on the market today.

Sliding garage door mechanism remote control ProfelmNet PSD-36T

The ProfelmNet PSD-36T remote control is tested and reliable. It has 4 buttons on which we can configure 4 different mechanisms (gates, shutters, overhead garage doors, etc.). It has a fixed 12-bit code at 433.92 MHz. It has a modern design and works excellently with the Autotech S5060T control panel.

Sliding mechanism installation process - Briefly

In summary, the steps for installing a sliding garage door mechanism are as follows:

• Checking that the door operates smoothly manually.
• Checking existing wiring or laying new wiring.
• After the checks, the motor base is installed. This requires a stable foundation. Usually, a reinforced concrete base is the appropriate solution.
• Mounting the motor on the base.
• Installing the rack.
• Installing accessories (if any).
• Checking the proper functioning of the entire system and explaining all details for safe use to users.

The above are simply a brief overview of the installation steps for a sliding mechanism. Inside the mechanism's package, you will find detailed, step-by-step instructions, well-written and easy to follow.

Disengagement of Proteco Meko-5 sliding automation

For greater safety, the Proteco Meko-5 mechanism is disengaged with a key. Insert the disengagement key into the lock and unlock it. Then, open the small door to its fully open position, and the motor now operates manually. By reversing the process (locking the small door), we reset and re-engage the mechanism.

Gear of PROTECO MEKO 5 mechanism

The gear of the Proteco Meko-5 mechanism is metal for greater durability and reliability. It has a protective cover to prevent accidents and protect users.

Packaging of the MEKO-5 (Kit-Basic) mechanism set

The MEKO-5 (Kit-Basic) set is delivered in one package containing the mechanism, the remote control, and any additional accessories that may have been ordered separately from the set.

The set is delivered ready for installation after being checked by our technicians and the remote control is configured.

Installation instructions for the sliding garage door kit

The kit is delivered with detailed instructions in Greek. They have been processed by us to be easy to follow even by people who are not directly involved in the subject.

They contain detailed steps for each stage of installation, from the motor base and rack to accessories such as photocells and buttons. Also included are detailed instructions for the Autotech S-5060T control panel, which is integrated into the mechanism.

Available documents for the Proteco Meko-5 motor (in English)

CE Declaration of Conformity

Installation Manual

Proteco Meko Sliding Automation Commercial Brochure